|
Our range of Water Proofing Systems is known for providing protection from water and moisture. We use latest nano and multi ceramic technologies to ensure that the adhesives and coatings not just meet but exceed the expectations of the clients. These systems have proved to be very effective for preventing seepage and corrosion due to water or moisture.
|
 | Waterproofing System | | |
| Waterproofing system using nano technology & multi ceramic technology Terraces & parapet walls
Total system gives high water resistance vapour permeable, resistance to moisture, uv stable, heat resistance.
bondcrete hr is polysiloxane base coating acts as a base coat and elastobond is top coat which eliminates conventional brick bat coba system also eliminates replastering of parapet and exteriordamp walls. Bondcrete hr, polysiloxane base coating all nanoparticles penetrate into cracks at the same time multiceramic technology base particles float on the top to bottom of the coating which areates water resistance and hydrophobicity.
due to combination of nano and multiceramic thechnology product gives high performance at the same times gives high dft with high coverage. |
| Exterior Wall Water Proofing System | | |
| our exterior wall waterproofing system gives thermal insulation,waterproofing and decorative look in single system which eliminates painting cost and having thickness 10 times than paint along with above properties. |
| Roof Parapet & Window Chazza Water Proofing System | | |
| Our roof parapet and window chazza waterproofing system gives permanant solution with membrane waterproofing and highly elastic system |
| Expansion Joint Water Proofing System | | |
| We also fabricate expansion joint water proofing systems which are known for their enhanced resistance to water and moisture. The elaborate construction provided with strong joints ensures that there is no seepage of water in the wall. Use of nano and ceramic technologies enables the particles to move freely and offer better resistance to moisture or water. Some of the features of the product are as follows: |
| Sheetwall Junction Water Proofing System | | |
| Providing & Applying PU Base Flexible Water Proofing layer sandwich with Polypropylene double layer membrane over the sheet & wall section. |
| Sheet Overlaps Section Water Proofing System | | |
| We are indulged in processing and exporting PU bases flexible water proofing layers. These products are quite similar to sheet wall junction water proofing systems. The only difference lies in overlapping of layers rather than them being joined. Here, polypropylene double layer membrane over the sheet overlaps with the section. Some of the features of the product are mentioned below: -
Accurate composition -
Longer shelf life -
Water resistant -
Corrosion resistant |
| Concrete / Metal Gutter Water Proofing System | | |
| We are engaged in providing and applying PU based flexible water proofing layer which is sandwiched with Polypropylene double layer membrane between the concrete / metal gutter sections. Only high quality and genuine raw material is used in the processing of these chemicals which ensures that the final water proofing layer is truly world class. Our product is used for water proofing different equipment like: -
Pipe line -
Pumps -
Valves -
Motors -
Construction machinery -
Air conditioning duct -
Transformers |
| Drain Outlets Water Proofing System | | |
| We also provide water proofing systems for ensuring better drainage systems across a variety of industries. These water proofing systems are basically PU based coatings, sandwiched with polypropylene double layer membrane over the junction of the drain. This system has proved to be very effective for preventing seepage and corrosion due to water or moisture. Our product is known for following basic features: -
Accurate composition -
Longer shelf life -
Environment friendly |
| Heat Resistant Waterproof Coating | | |
| SMAC® BONDCRETE HR is a super-polymer modified heat resistant waterproof coating for cementitious substrates. It is a Nano-technology and Multi-ceramic technology based high performance surface coating, specially tailored for Indian climatic conditions.
WORKING PRINCIPLES:
When SMAC® BONDCRETE HR is applied on cementitious surface, Nano-technology based Intelligent Chemicals react with cementitious materials and the nano-particles penetrate into capillaries. There, these reaction complexes & nano-phases create hydrophobicity.
Multi-ceramic technology based particles remain active on the top and bottom surface of the
formed coating. This ceramic particle layer is 100% inert and non-conductive in nature. Hence SMAC® BONDCRETE HR treatment gives high water resistance as well as heat resistance property.
APPLICATION PROCEDURE:
First remove all loose particles and remove oil, grease and other loose materials contaminated on the surface. Clean the surface by water. Fill all the cracks, honey-combs, voids etc using cement mortar or our BONCRETE RP repair compound. A 10% muriatic acid solution wash should follow. Again wash the surface with plenty of water. Let the surface dry to SSD (saturated surface dry) condition. Apply one coat of SMAC® BONDCRETE HR by brush. Second coat should be applied when the first coat is slightly tacky to touch, preferably in a perpendicular direction to the first coat. |
| Elastomeric Heat Reflective Coating | | |
| SMAC® ELASTOBOND is an elastomeric heat reflective coating made from a blend of super-polymer emulsions modified with Multi-ceramic and Nano-technology based chemicals. It is an elastic coating which waterproofs & protects roof slabs, walls etc against excess heat, mild chemicals & cracking related leakages.
ACTION MECHANISM:
SMAC® ELASTOBOND is a liquid formulation which is an organic polymer combination fortified with multi-ceramic & nano-tech based chemicals. Because of the nature of chemicals in the formulation, heat is effectively reflected from the surface treated &
temperature rise is reduced. The coating forms a weather & waterproof barrier over the treated surface. Further, the flexibility of the coat takes care of future cracking, if any, in the substrate.
ADVANTAGES:
• Elasticity up to 300%
• Heat reflective nano-tech barrier; Cooling load is
reduced
• Highly water repellent
• Waterproof
• Lets the substrate “Breathe”; Indoor condensation minimal
• Sulphate and Chloride penetration resistance
• Anti-fungal property prevents defacement
TECHNICAL DATA:
• Base: Special Polymer Blend Emulsion with Multi-ceramic & Nano-tech chemicals
• Solid content: 50±2%
• Colour: White or as per customer requirement
• Viscosity: 250-500 cps
• pH: 8.5±0.5.
• Flexibility: 300%
• DFT in two coats:1000 micron
• Recommended coats: Two
APPLICATION PROCEDURE:
While applying SMAC® ELASTOBOND coat, surface preparation is the most important part. Remove all the loose materials to expose the base surface of the wall. Wash the surface with plenty of water. A 10% muriatic acid solution wash should follow. Again wash the surface with plenty of water. Let the surface dry to SSD (saturated surface dry) condition. Fill all the cracks, honey-combs, voids etc using cement mortar or our BONDCRETE RP repair compound. Apply a coat of SMAC® ELASTOPRIMER for wall or two coats of SMAC® BONDCRETE HR slabs liberally by brush over the surface. Allow the surface to be touch-dry. Apply a coat of SMAC® ELASTOBOND on the primed surface by brush. Care must be taken to ensure a uniform coat without brush marks. The second coat should be applied after the first coat is dry to touch. The second coat should be applied perpendicular to the first coat. Protect the treated surface for 48 hours from
direct water splashes, scratching & other disturbances. Wash all the tools with water & soap. |
| Polyurethane Based Flexible Sealant | | |
| SMAC® ELASTOSEAL is a single component, Polyurethane based, Polysiloxane modified elastomeric sealant for filling cracks in internal and external plastered surfaces as well as concrete expansion & construction joints. It can be applied to damp surfaces and is ‘Invisible’ after application & curing.
ADVANTAGES:
- After installation, no visible crack-filling marks are there
- Can be installed on damp plaster or concrete
- Resistance to alkali silica reaction (ASR)
- Elastomeric and remains permanently flexible
- UV stable
- Excellent adhesion on cementitious substrate
- Eco-friendly, being water based composition
- No sanding of the surface is required while installing SMAC® ELASTOSEAL
APPLICATION PROCEDURE:
The crack or crevice to be filled should be cleaned by mechanical means. If required, the crack should be opened in a ‘U’ shaped groove and cleaned properly to remove loose materials & laitance. Apply a coat of SMAC® ELASTOPRIME S primer, which enhances proper bond with the substrate and also penetrates the adjoining area to seal it against water ingress. Fill the crack with help of putty knife and level properly. Wash hands and equipment
with soap and water. Let the sealant cure. Touch dry & full curing time at 30⁰ C is about 2 hours at 60% humidity. In rainy seasons, the time required for full curing can be about 8 hours. For expansion joint & Tremix floor joint filling & detailed procedure thereof, please contact the technical division of our company.
APPLICATIONS:
- Internal and external plaster cracks
- Tremix floor joint seals
- Beam-masonry and column-masonry joints
- Expansion joints
- Construction joints
|
| Water Based Primer | | |
| SMAC® ELASTOPRIMER is a highly concentrated polymer modified penetrant primer for cementitious and mineral substrates. It forms a medium hard and elastomeric film over the substrate. Due to its application, absorption and consumption of subsequent coating material is reduced. Also, it acts to block capillaries in the substrate because of its penetrating chemicals & hence improves waterproofing performance.
ADVANTAGES:
• Eco friendly
• Waterproofing improver
• High coverage
• Reduces consumption of waterproof coating.
• Alkali resistance
• Improves bonding between the substrate and top coating layer
SPECIAL APPLICATION PROPERTY:
When SMAC® ELASTOPRIMER is applied before waterproof coating, it improves waterproofing properties. Due to higher percentage of polymers fortified with nano-tech chemicals, it penetrates
into porous substrate. This process blocks all capillaries and produces waterproofing effect.
Further, it reduces consumption of waterproof coating and improves coverage.
COVERAGE:
- 14 to 15 sq. m. in one kg
PACKING:
- 20 kg and 50 kg HDPE containers
|
| Special Lotus Effect Elastomeric Heat Reflective Coating | | |
| SMAC® ELASTOBOND SLE is an elastomeric heat reflective coating based on high quality polymer emulsion modified with multi-ceramic and nanotechnology which gives Special Lotus Effect on the treated surface.
ACTION MECHANISM:
SMAC® ELASTOBOND SLE is a liquid formulation which is an organic polymer combination fortified with multi-ceramic & nano-tech based Intelligent Chemicals. The molecules of these Intelligent Chemicals have penetrating ability in the substrate to seal the capillaries. It also provides heat insulation effect because of SMAC® Therm technology. The nano particles form a weather & waterproof barrier over the treated surface. Further, the flexibility of the coat takes care of future cracking, if any, in the substrate.
ADVANTAGES:
• Elasticity up to 300%
• Heat reflective nano-tech barrier; Cooling load is reduced
• High gloss
• Highly water repellent with Special Lotus Effect
• Waterproof
• Easy to clean and high dirt pick-up resistance
• Lets the substrate “Breathe”; Indoor condensation minimal
• Sulphate and Chloride penetration resistance
• Anti-fungal property prevents defacement
• Breathable
TECHNICAL DATA:
• Base: Special Polymer Blend Emulsion with Multi-ceramic & Nano-tech Intelligent Chemicals
• Solid content: 50±2%
• Colour: White or as per custom colours
• Viscosity: 250-500 cps
• pH: 8.5±0.5.
• Flexibility: 300%
• DFT in two coats:1000 micron
• Recommended coats: Two |
| Ecofriendly Exterior Paint | | |
| ELASTOBOND EX is self crosslink 100 % pure acylic base exterior paint which modified with nano polysiloxane polymer to increase exterior durability.
Properties:
- Ecofriendly
- Waterproof
- Self crosslinking
- Good outdoor durability
- Excellent dirt pickup resistance
- Alkali resistance
- High bonding strength than conventional paint Antifungus
Coverage : 150 sq.ft in one coat
Thinning : by portable water
Priming : use elastoprimer
Packing : 20 kg
Shelf life : 12 months |
|
 Product
Showroom View all our products / services as a slide show. play now
|
